Materials Research

Publicação

Analysis of the mechanical properties and characterization by solid state 13C NMR of Recycled EVA Copolymer/Silica Composites

Optimization of the Magnetic Properties of Materials for Fluxgate Sensors

Comparison of two different synthesis methods of perovskites SrCo0.5FeO3 type, aiming at their use as membranes for partial oxidation of methane

Effect of Solidification Processing Parameters and Silicon Content on the Dendritic Spacing and Hardness in Hypoeutectic Al-Si Alloys

Surface properties of dental polymers: measurements of contact angles, roughness and fluoride release

Development of Bulk Bi(2+x)Sr(3-y)CayCu2O(8+delta) Superconductors by Partial-Melting Route for Fault Current Limiters Applications

Effect of therapeutic dose X rays on mechanical and chemical properties of esthetic dental materials

Predicting Secondary-Dendrite Arm Spacing of the Al-4.5wt%Cu Alloy During Unidirectional Solidification

Effects of Local Heat Input Conditions on the Thermophysical Properties of Super Duplex Stainless Steels (SDSS)

Sigma Phase in Superduplex Stainless Steel: Formation, Kinetics and Microstructural Path

Simulation of the solidification of pure nickel via the phase-field method

Comparison of two different synthesis methods of perovskites, SrCo0.5FeO3 type, aiming at evaluating their use as membranes for partial oxidation of methane

Influence of Nanoxides on Diffusivity and Solubility of Hydrogen in Pd-based alloys

Effects of Thermal Aging on Microstructure and Corrosion Resistance of AISI 317L Steel Weld Metal in the FSW Process

Influence of Microstructure on the Corrosion Resistance of AISI 317L (UNS S31703)

Influence of Heat Treatments on the Impact Toughness of a Ti-stabilized 12%Cr Supermartensitic Stainless Steel

Effect of Mo concentration and aging time on the magnetic and mechanical hardness of Fe-xMo-5Ni-0.05C alloy (x=5, 8,11 and 15 wt.(%))

Deformation Induced Martensite in an AISI 301LN Stainless Steel: Characterization and Influence on Pitting Corrosion Resistance

475oC embrittlement in a duplex stainless steel UNS S31803

Experimental Investigation of Ternary Al-Si-Cu Alloy Solidified with Unsteady-State Heat Flow Conditions

Continuous Scanning Technique with Barkhausen Magnetic Noise for Carbon Steel Sheets

Influence of Heat Treatment in Residual Stresses Generated in P91 Steel-pipe Weld

Influence of Deleterious Phases Precipitation in the Corrosion Resistance Measured by Double Loop Electrochemical Polarization Reactivation Test in Superduplex Stainless Steel

Ballistic Efficiency of Multilayered Armor Systems with Sisal Fiber Polyester Composites

Evaluation of the Diameter Influence on the Tensile Strength of Pineapple Leaf Fibers (PALF) by Weibull Method

Flexural Behavior of Epoxy Matrix Composites Reinforced with Malva Fiber

Topological and metrical aspects of normal and abnormal grain growth

Formal analysis of isothermal martensite spread

Formation of Microphases and Constituents from Remaining Austenite Decomposition in API X80 Steel Under Different Processing Conditions

Inhomogeneous Poisson point process nucleation: comparison of analytical solution with cellular automata simulation

A Short review on wrought austenitic stainless steels at high temperatures: processing, microstructure, properties and performance

Microstructural Path Analysis of Martensite Dimensions in FeNiC and FeC Alloys

Microstructural descriptors and cellular automata simulation of the effects of non-random nuclei location on recrystallization in two dimensions

Analysis of transformations nucleated on non-random sites simulated by cellular automata in three dimensions

Cellular automata simulation of site-saturated and constant nucleation rate transformations in three dimensions

Simulation of recrystallization in iron single crystals

Modeling polycrystals with regular polyhedra

Microstructural Evolution of a Pearlitic Steel Subjected to Thermomechanical Processing

Effect of textile waste on the mechanical properties of polymer concrete

Mechanical characterization of fiber reinforced Polymer Concrete

Mechanical characterization using optical fiber sensors of polyester polymer concrete made with recycled aggregates

Effect of Exposure Time vs. Irradiance on Knoop Hardness of Dental Composites

Influence of Ethanol Concentration on Softening Tests for Cross-link Density Evaluation of Dental Composites